Search results for: 'Airbag'
- Related search terms
- Airbags for 2004 2500 chevy
- Airbags for 2019 gmc 2500
- airbags ford 2019 gmc 2500
- Airbags
- Airbag brackets
- Porterbuilt 1963-72 C10 Rear Dropmember - Level 1 Mild, Airbag
The Dropmember Rear modular suspension system is designed to replace the factory components and improve ride quality, performance, aesthetics, and strength.
DOES NOT REQUIRE ANY BED FLOOR MODIFICATION!
Ride Height - 7"
Learn More
Deflated Height - 3"$2,399.00 - Porterbuilt 1973-87 C10 Rear Dropmember - Level 1 Mild, Airbag
The Dropmember Rear modular suspension system is designed to replace the factory components and improve ride quality, performance, aesthetics, and strength.
DOES NOT REQUIRE ANY BED FLOOR MODIFICATION!
Ride Height - 7"
Learn More
Deflated Height - 3"$2,399.00 - Porterbuilt 1963-72 C10 Rear Dropmember - Level 3 Extreme, Airbag
The Dropmember Rear modular suspension system is designed to replace the factory components and improve ride quality, performance, aesthetics, and strength.
Ride Height - 4"
Learn More
Deflated Height - Lay Frame$2,399.00 - Porterbuilt 1973-87 C10 Rear Dropmember - Level 3 Extreme, Airbag
The Dropmember Rear modular suspension system is designed to replace the factory components and improve ride quality, performance, aesthetics, and strength.
Ride Height - 4"
Learn More
Deflated Height - Lay Frame$2,399.00 - Porterbuilt 1963-72 C10 Front Dropmember - Level 1 Mild, Airbag
The 1963-72 Chevy Pickup Front Dropmember suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 1 Front will set the lowest point of the factory frame rails approximately 3" off of the ground when fully deflated.Ride Height - 6-7"
Deflated Height - 3"
Learn More$1,399.00 - Porterbuilt 1973-87 C10 Front Dropmember - Level 1 Mild, Airbag
The 1973-87 Chevy Pickup Front Dropmember suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 1 Front will set the lowest point of the factory frame rails approximately 3" off of the ground when fully deflated.Ride Height - 6-7"
Deflated Height - 3"
Learn More$1,399.00 - Porterbuilt 1" Narrowed Control Arms - Version 7 Dropmember, Airbag
Porterbuilt tubular control arms are built using thick-wall DOM tubing and CNC cut 3/16 pickeled plate steel. All bushing pivot tubes and ball joint cups are TIG welded.
Learn More
1" NARROWED
FOR VERSION 7 DROPMEMBER ONLY$1,099.00 - Porterbuilt Front Swaybar - Version 7 DropmemberPorterbuilt front swaybar for 1963-87 Version 7 Dropmember equipped trucks.
Fits Level 2 Coilover and Level 3 airbag kits only!
DOES NOT FIT LEVEL 1 DROPMEMBER KITS! Learn More$349.00 - Porterbuilt 1963-72 C10 Front Dropmember - Level 3 Extreme
The 1963-72 Chevy Pickup Front Dropmember suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 3 Front will set the lowest point of the factory frame rails on the ground when fully deflated.Ride Height - 4"
Deflated Height - Lay Frame
Learn More$1,399.00 - Porterbuilt 1973-87 C10 Front Dropmember - Level 3 Extreme
The 1973-87 Chevy Pickup Front Dropmember suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 3 Front will set the lowest point of the factory frame rails on the ground when fully deflated.Ride Height - 4"
Deflated Height - Lay Frame
Learn More$1,399.00 - Porterbuilt 1963-72 C10 Front Dropmember - Level 3 Extreme
The 1963-72 Chevy Pickup Front Dropmember suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 3 Front will set the lowest point of the factory frame rails on the ground when fully deflated.Ride Height - 4"
Deflated Height - Lay Frame
Learn More$1,399.00 - Porterbuilt 1960-62 C10 Rear Dropmember - Level 3 ExtremeThe Porterbuilt Dropmember Level 3 1960-62 Chevy Pickup Rear suspension system is engineered to lay body with large diameter wheel/tire combinations. (Recommended to run no wider than a 10” wheel). Learn More$2,399.00
- Porterbuilt 1963-87 Stage 1 Front KitLooking for an easy way to switch over to air suspension without breaking the bank? The Stage 1 front kit is an inexpensive and simple way to do just that! The Stage 1 front kit is designed to replace the factory steel coil spring with an air spring while maintaining the factory control arms. C10 SHOP EXCLUSIVE! Learn More$599.00
- Porterbuilt 1963-72 Stage 1 Rear KitThe Porterbuilt Stage 1 rear kit is both an economical and easy way to lower the rear of your 63-72 C10′s trailing arm suspension. The air spring and mounting plates replace the factory steel coil spring, allowing a better ride quality and adjustability! The Stage 1 shock relocator brackets improve shock function by decreasing the shock angle! C10 SHOP EXCLUSIVE! Learn More$599.00
- Air Fitting Kit 3/8" Air LineIncludes Four SMC 3/8" PTC Fittings (D.O.T. Approved)
5 Options available:
Four 1/2" npt x 3/8" PTC Air Fittings - Elbow Male
Four 1/2" npt x 3/8" PTC Air Fittings - Straight Male
Two 1/2" npt x 3/8" PTC Elbow & Two 1/2" npt x 3/8" PTC Straight
Two 1/2" npt x 3/8" PTC Elbow & Two 1/4" npt x 3/8" PTC Elbow
Two 1/2" npt x 3/8" PTC Straight & Two 1/4" npt x 3/8" PTC Elbow Learn More$26.00 - Porterbuilt Air Management BracketsFrame mounted brackets that hold one compressor and 3 gallon tank.
Includes 2 brackets.
Tanks & compressors not included. Learn Morewas $199.00 Special Price $189.00 - Porterbuilt SBC Motor Mounts, Dropmember Version 7Porterbuilt Fabrication Version 7 Dropmember SBC Motor Mounts
Available in SBC, BBC, LS, & LT Configurations Learn More$249.00 - Porterbuilt BBC Motor Mounts, Dropmember Version 7Porterbuilt Fabrication Version 7 Dropmember BBC Motor Mounts
Available in SBC, BBC, LS, & LT Configurations Learn More$249.00 - Porterbuilt LT Motor Mounts, Dropmember Version 7Porterbuilt Fabrication Version 7 Dropmember LT Motor Mounts
Available in SBC, BBC, LS, & LT Configurations Learn More$249.00 - Porterbuilt Raised Bed Floor Mounts - 1963-72Raised Bed Floor Mounts for 1963-72 Dropmember Equipped Trucks
NOW INCLUDES MOUNTING BRACKETS FOR BOYD FUEL TANK Learn More$649.00 - Porterbuilt Raised Bed Floor Mounts - 1973-87Raised Bed Floor Mounts for 1963-72 Dropmember Equipped Trucks
NOW INCLUDES MOUNTING BRACKETS FOR BOYD FUEL TANK Learn More$649.00 - Low Profile LSX Swap Oil Pan Kit, F-BodyLow Profile Oil Pan Kit
LSX Engine, F-Body Oil Pan
Fits 4.8L, 5.3L, 6.0L, 6.2L
Dropmember Compatible
Learn Morewas $349.00 Special Price $329.00 - Low Profile LT Swap Oil Pan KitLow Profile LT Oil Pan Kit
LT GEN V, A BODY, G BODY
Fits LT1, LT4, L83, L86, 5.3L, 6.2L
Dropmember Compatible Learn Morewas $379.00 Special Price $359.00 - Porterbuilt 1963-87 1" Narrowed Control Arms - Factory Crossmember
Porterbuilt tubular control arms are built using thick-wall DOM tubing and CNC cut 3/16 pickeled plate steel. All bushing pivot tubes and ball joint cups are TIG welded.
Learn More
1" NARROWED
FOR FACTORY CROSSMEMBER ONLY!$1,099.00 - Porterbuilt 1963-87 1" Forward & 1" Narrowed Control Arms - Factory Crossmember
Porterbuilt tubular control arms are built using thick-wall DOM tubing and CNC cut 3/16 pickeled plate steel. All bushing pivot tubes and ball joint cups are TIG welded.
Learn More
1" FORWARD & 1" NARROWED
FOR FACTORY CROSSMEMBER ONLY!$1,099.00 - Porterbuilt 1963-87 1" Forward & 1" Narrowed Control Arms - Factory Crossmember
Porterbuilt tubular control arms are built using thick-wall DOM tubing and CNC cut 3/16 pickeled plate steel. All bushing pivot tubes and ball joint cups are TIG welded.
Learn More
1" FORWARD & 1" NARROWED
FOR FACTORY CROSSMEMBER ONLY!$1,099.00